Lavemi Men's Real Leather Ratchet Dress Belt with Automatic Buckle,Elegant Gift Box

التعليق

IMO this would be a great belt if it were properly designed. Unfortunately, IMO, it is not well designed and represented. The ratchet receptor area on the belt is only 7.25 inches and the inner portion is not feed through like on the military belts, there is a block. That means you dont have the ability to change the range in either direction once the belt is cut. Correcting these issues would make this belt a great belt. Refer to the military style canvas belts for the proper way a slide belt should be as they are adjustable on the outside and inside and have a full grab range on the belt. I returned mine. I would have never bought had I known this.

إظهار المزيد

التعليق

My big buck slide belt wore out the compressed and laminated leather product belt in nine months. I am a big guy and will admit to being tough on leather belts - but that belt and buckle were not as robust in construction as this Dante belt. I liked the Dante belt so much that I bought my older son one for Christmas - then I bought myself a spare! The three Dante belts totaled just less than what I had spent on the real slide belt - they are a true bargain. The belt comes nicely packaged in a gift box, which was shipped in a padded mailer, arriving here in two days each time. The belt itself is black and slightly wider and thicker and made of rawhide, an improvement over the other brand. The gunmetal colored buckle is more robust, too - and by this time, after nearly two months of constant use, the other buckle was looking ratty an had started falling off - not the Dante. It is size limited -~43" - maybe 44" max. The ratchet has more teeth per linear length making for finer adjustments. It looks fine with all of my work, casual, and dress pants, too, but I have never been very fashion-conscious. One caveat - if you get the belt too tight, you will have to get some of the tension off the belt before it will release by the buckle release below the buckle... ie, suck your gut in! I like it!

إظهار المزيد

التعليق

The belt will come big enough to fit a 44" waist, but you will see vertical guidelines for different waist sizes which you are supposed to cut with any scissors. Most belts have little holes spaced about an inch apart; you tighten or loosen the belt by setting the buckle tongue from one hole to another; this means you can tighten or loosen the belt "by the inch". This belt isnt like that. Instead of a buckle tongue, its a ratchet type of belt where youd hear clicking sounds as you tighten it; then to loosen it, you pull a small piece of metal outward, and that releases the belt loose. I wasnt sure I liked this at first, until I realized how finely you can tighten the belt; this gives you very precise control on how tight you want the belt to be. Its a great design, in my humble opinion, and I have come to love it. I just hope its durable, and it does feel solid and robust, so I hope Ill be using this for many years to come. You should try it; Im sure you will like the precision-tightening feature of this belt.

إظهار المزيد

التعليق

I gave this five stars because I have never found a belt anywhere near this quality for the price. The packaging is higher-end which would make this good as a gift, but I bought this for myself and I will find a good re-purpose for the box and belt bag. The look of the belt is sleek and works good with my office clothes. The engineering of the belt is great and the ratcheting makes for an exact fit. There are two properties of the belt I want to warn you about though. First, the belt face does scratch easily (I got all black). I immediately got a small scratch in the paint and now I am extremely careful about not carrying anything that rubs on it, or dropping my pants on floor with the belt still on. The second item is that you should absolutely read and follow the directions. There are several inches of belt that extend past a tracked section on the rear of the belt that is required to fasten your belt. When you calculate the cut point you have to account for this extra belt that must always extend past the buckle. I did not read the directions and went straight to cutting thinking I could run the end of the belt just past the buckle. Nope. Luckily I cut short and it works great for now. If I gain more than an inch in my waist Ill need a new belt, but thats my fault, not the belt. The instructions were clear, after I eventually read them. When I get another one, Ill be getting another of these!

إظهار المزيد

التعليق

First off, this belt is real leather (with a textured outer layer.) All of the moving parts are made of metal, with the exception to the ratchet teeth on the belt (made of hard, durable, plastic.) The patterns are sophisticated yet not too gawdy. Yes, the buckles paint will probably scrape off if you scrape the belt against stuff but that literally happens to every belt buckle ever created. After all, belt buckles are not made of Titanium Alloy with a layer of Cerakote paint and they likely never will be lol. Anyways, only time will tell how this belt holds up. So far so good. I dont anticipate the leather cracking over time unless it is folded together sharply several times in the exact same spot. To release the belt, all you have to do is pull on a lever by the buckle housing; Im not sure why everyone is saying that it takes a while to get used to. Seriously, its quicker to put on/take off than a traditional belt. Another nice touch worth noting is that it includes instructions if you somehow cant figure out how to use the belt. The packaging is also top-notch because it includes individually bagged and protected components within a textured black box with "Dante" embossed on the top. Lastly, to further help you setup/trim the belt to your waist, the cuttable end has inches marked by increments of 1" so that there is no need to "eyeball it." All you have to do is wear the belt as it comes out of the box, see how much you wanna cut off, take off the buckle, and then cut off the amount. ONE more important thing, sorry: be sure to use a lighter to get rid of any frayed stitching/strings around the plastic notches or edges of the belt. There might be a small possibility of any hanging strings getting stuck in the belt ratcheting mechanism. Update: over 2 months later, and this belt is still holding strong. Not a single chip or scratch either on the buckle. This may be due to me being concious of not dragging the buckle/bumping into stuff

إظهار المزيد